Search found 196 matches

by Arnold
Thu Dec 02, 2010 11:46 pm
Forum: Tech Support
Topic: yanmar 2210d thermostart UPDATE
Replies: 7
Views: 4915

Re: yanmar 2210d thermostart

As Alan suggested, it might be in the throttle linkage. I'd sit on the tractor and when it idles down, I'd move the throttle and see f you can keep it running. if you can it's somewhere in the linkage. When I first read your post I thought it may be something restricting the fuel flow. If it were a ...
by Arnold
Thu Nov 25, 2010 11:50 pm
Forum: Tech Support
Topic: like my harvest
Replies: 16
Views: 7058

Re: like my harvest

The shaft on the PTO is driving an eccentric up and down (small amount). This causes the bed to move up and down while the machine moves forward. Does this make the harvesting easier? Also might want to consider having an operator on the tractor while it's moving. Mounting a moving tractor (stepping...
by Arnold
Thu Nov 25, 2010 11:41 pm
Forum: Tech Support
Topic: Battery group for 135D
Replies: 4
Views: 4519

Re: Battery group for 135D

I'm sure someone has a book for the required battery group. What I normally do is measure the existing battery (assuming someone didn't put a small battery in the tractor) and then go to the store and buy one that's the same size. Also, look at the cold cranking amps (CCA) on the existing battery an...
by Arnold
Thu Nov 18, 2010 8:49 pm
Forum: Tech Support
Topic: Basic YM-155D info
Replies: 7
Views: 4436

Re: Basic YM-155D info

A good starting point would be to buy a service manual (Hoye sells them). The manual will provide service information and tell you where all the grease and oil points are located at.

Did the 155 come with any attachments (loader, back blade)? What are you planning to use the tractor for?
by Arnold
Tue Nov 02, 2010 11:26 pm
Forum: Tech Support
Topic: Starter Solenoid on YM155D
Replies: 10
Views: 4852

Re: Starter Solenoid on YM155D

Eagle, The solenoid is just an eletro-magnet. You apply voltage to the coil and and the device develops a magnetic field and moves the metal cylinder inside the coil. Two possible problems: if the wire (coil inside) is broken the magnetic field won't develop. Check the wire to make sure it has conti...
by Arnold
Mon Nov 01, 2010 10:45 pm
Forum: Tech Support
Topic: like my harvest
Replies: 16
Views: 7058

Re: like my harvest

Alan, How can you tell someone is posting from a foreign country? and which foreign country? Not sure which web site you are using to do your translations. I use Google translate (it's something like Google.translate/#, I can send web address if you are interested) at work and it seems to work well ...
by Arnold
Fri Oct 29, 2010 8:01 pm
Forum: Tech Support
Topic: like my harvest
Replies: 16
Views: 7058

Re: like my harvest

I think you eat a little later in Spain (9:26pm) than we do in the US. Last summer I saw an antique potato harvester. Fairly complicated device (considering it was about 75 years old) with a conveyor belt that started underground and delivered the picked potatoes on top. Did you hand pick your potat...
by Arnold
Sun Oct 24, 2010 3:34 pm
Forum: Tech Support
Topic: PTO gear selecting
Replies: 14
Views: 9050

Re: PTO gear selecting

The speed of the PTO depends on the gear selected and the RPM of the engine. Obviously you want the engine running in an RPM range where it's not lugging and where it's putting out the right amount of horsepower. Your first post said you are able to use the 540 gear selection. Most implements are 54...
by Arnold
Sat Oct 23, 2010 7:17 pm
Forum: Tech Support
Topic: yanmar diesel tractor ym 240
Replies: 5
Views: 3015

Re: yanmar diesel tractor ym 240

Sonny,
I don't think the problem is common. Try to do a search on this site using keywords "240" and "high low lever".
by Arnold
Sat Oct 23, 2010 7:11 pm
Forum: Tech Support
Topic: PTO gear selecting
Replies: 14
Views: 9050

Re: PTO gear selecting

When you say "push down" I assume you mean the clutch. On my tractor the PTO works just like a transmission. Push the clutch in, move the PTO lever to the range you want, let the clutch out, and away she goes. You are using the clutch aren't you?
by Arnold
Fri Oct 22, 2010 10:18 pm
Forum: Tech Support
Topic: PTO gear selecting
Replies: 14
Views: 9050

Re: PTO gear selecting

Most attachments are rated to run 540 rpm. Is the attachment that you will be using 540 or 1000?
by Arnold
Fri Oct 22, 2010 10:11 pm
Forum: Tech Support
Topic: yanmar diesel tractor ym 240
Replies: 5
Views: 3015

Re: yanmar diesel tractor ym 240

Have you used the selector before? Did anything happen just prior to not working?
by Arnold
Wed Oct 20, 2010 9:18 pm
Forum: Tech Support
Topic: engine wont rev
Replies: 6
Views: 3744

Re: engine wont rev

Sounds like the injectors were tested off the tractor. Glad they are working correctly but they need to deliver the fuel shot at the right time. I would start with the timing and also make sure the pump is delivering the right amount of pressure to the injectors. Did someone re-build the motor for y...
by Arnold
Tue Oct 12, 2010 11:14 pm
Forum: Tech Support
Topic: 2000BD slight gear grinding with clutch down
Replies: 7
Views: 3562

Re: 2000BD slight gear grinding with clutch down

FL_Jerry Adjusting the clutch on a tractor is the same as any other vehicle (with a manual transmission). You want a little free travel of the pedal before it activates the throw out bearing (see Winstons message on how much free play). Too much free play and the clutch won't disengage; to little fr...
by Arnold
Tue Oct 05, 2010 11:58 pm
Forum: Tech Support
Topic: YM1510D will not run.
Replies: 14
Views: 6636

Re: YM1510D will not run.

Make sure there is an open vent under the fuel cap. One quick way to determine if this is the problem would be to crack the fuel cap and see if it alleviates the fuel flow problem.

Go to advanced search