Search found 13 matches

by Bkfym2000
Thu May 07, 2020 5:54 pm
Forum: Tech Support
Topic: Ym2000 hydraulic pump is deadheading
Replies: 1
Views: 360

Ym2000 hydraulic pump is deadheading

I have a ym2000 with a 285 bulldog loader. the bucket would barely move and the three point wouldn’t raise. After blowing all the lines out and replacing the fluid the three point would raise but not stay up and the loader moved a little faster but still very slow. I replaced the pump and now the ne...
by Bkfym2000
Wed Feb 26, 2020 10:43 pm
Forum: Tech Support
Topic: Ym2000 loader working but three point won’t raise
Replies: 19
Views: 4865

Re: Ym2000 loader working but three point won’t raise

I have not done that. But I think I will so verify. It’s presenting like there is a clogged like but I have drained and checked the system twice and find any blockages. I am wondering if the control valve for the loader that I have is maybe the wrong one? I’m wondering if I need a power beyond unit.
by Bkfym2000
Wed Feb 26, 2020 11:36 am
Forum: Tech Support
Topic: Ym2000 loader working but three point won’t raise
Replies: 19
Views: 4865

Re: Ym2000 loader working but three point won’t raise

I capped the bucket boom inlet and outlet, as well as the curl inlet and outlet. I only left the supply hose and the return hose that feeds the three point. I placed an in-line pressure gauge on the inlet hose at the point it connects to the control valve for the loader. With the engine turned on an...
by Bkfym2000
Tue Feb 25, 2020 9:15 pm
Forum: Tech Support
Topic: Ym2000 loader working but three point won’t raise
Replies: 19
Views: 4865

Re: Ym2000 loader working but three point won’t raise

Ok guys, sorry to keep asking questions but I put a pressure gauge on the hydraulic system and found that the system is only pushing 1000 psi. Is this indicative of the pump failing or is there something else I can do to dial up the pressure ?
by Bkfym2000
Thu Feb 20, 2020 1:01 am
Forum: Tech Support
Topic: Ym2000 loader working but three point won’t raise
Replies: 19
Views: 4865

Re: Ym2000 loader working but three point won’t raise

The arms raise freely by hand. They are in the down position.
by Bkfym2000
Wed Feb 19, 2020 12:05 pm
Forum: Tech Support
Topic: Yanmar ym2000 starter issue
Replies: 3
Views: 2068

Re: Yanmar ym2000 starter issue

Yes it still working. Just bogs after the first start. Your suggestion makes a lot of sense. Would that be more of a solenoid problem then? It not retracting the gear after start up? Or maybe something jammed? I’m going to try and take it apart tomorrow. Since I can’t finish troubleshooting the load...
by Bkfym2000
Tue Feb 18, 2020 7:34 pm
Forum: Tech Support
Topic: Yanmar ym2000 starter issue
Replies: 3
Views: 2068

Yanmar ym2000 starter issue

So the saga continues in this tractor. Suddenly the tractor starts fine when sitting for a while and completely cold, then after running for a while the starter starts smoking. Then when I turn it off and try to start it again, the starter sounds like the battery is dead. It tries cranking but just ...
by Bkfym2000
Sun Feb 16, 2020 6:22 pm
Forum: Tech Support
Topic: Ym2000 loader working but three point won’t raise
Replies: 19
Views: 4865

Re: Ym2000 loader working but three point won’t raise

Thanks Winston that makes since you by pass the loader and just verify the three point works. The loader is a bulldog 285. Also this is the route that top loader loader hose. I traced the line and labeled it for you. Someone else also mentioned the relief valve could be opened too far and there’s no...
by Bkfym2000
Sun Feb 16, 2020 1:36 pm
Forum: Tech Support
Topic: Ym2000 loader working but three point won’t raise
Replies: 19
Views: 4865

Re: Ym2000 loader working but three point won’t raise

the top hose on the valve attached to the steel line via an elbow connector circled in the picture. I don’t see any identifying marks on the valve, but it looks original. Missing the filter wouldn’t cause this issue correct?
by Bkfym2000
Sun Feb 16, 2020 12:55 pm
Forum: Tech Support
Topic: Ym2000 loader working but three point won’t raise
Replies: 19
Views: 4865

Re: Ym2000 loader working but three point won’t raise

So it has six lines coming out of the loader control valve body. I attached a diagram and some photos of how it is currently set up. Last night I took apart the three point control valve, very thing was moving and nothing stuck, no internal rust. I also to the three point cylinder partially apart an...
by Bkfym2000
Sat Feb 15, 2020 7:38 pm
Forum: Tech Support
Topic: Ym2000 loader working but three point won’t raise
Replies: 19
Views: 4865

Re: Ym2000 loader working but three point won’t raise

I got it this way. I loosened the the hose that Goes from the joystick control valve to the three point system and there is fluid coming out of it but it doesn’t seem like it’s coming out as quickly as maybe it should? Also I noticed that the hoses on the control valve/joystick are super hot even wh...
by Bkfym2000
Sat Feb 15, 2020 10:47 am
Forum: Tech Support
Topic: Ym2000 loader working but three point won’t raise
Replies: 19
Views: 4865

Ym2000 loader working but three point won’t raise

I have a ym2000. The loader works but the three point system will not raise. I figure the pump is not the issue since the loader is working and I have already checked and made sure the valve under the seat is backed all the way out and still nothing on the three point. Is there another diverted vale...

Go to advanced search