Search found 41 matches

by dagnblond
Tue Jun 30, 2020 12:23 pm
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

found the blockage and replaced the control for FEL but still have the 3 point dropping issue so I sent it to the tractor hospital, it was obviously beyond my abilities
by dagnblond
Fri Jun 05, 2020 2:19 pm
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

took the controller off replaced the o-rings and think I put it together just like it came apart but when I started the tractor to test it it started and shut right back off a couple times then it started and blew the side off the controls for the FEL so I'm thinking it's building way too much press...
by dagnblond
Mon Jun 01, 2020 10:40 am
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

better pic this is on right side under the hyd line under seat
tractor lift 7.jpg
tractor lift 7.jpg (108.45 KiB) Viewed 513 times
by dagnblond
Sun May 31, 2020 6:02 pm
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

what is this adjustment knob for
tractor lift 5.jpg
tractor lift 5.jpg (99.86 KiB) Viewed 527 times
by dagnblond
Sun May 31, 2020 1:08 pm
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

by dagnblond
Sun May 31, 2020 1:06 pm
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

the 4 around the lock out under the front of the seat, I tried pulling the lock out itself but the piston won't come out
by dagnblond
Sun May 31, 2020 12:31 pm
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

got a little time today but it's tough working out in 90 plus degrees took arms off and there is a good bit of side to side movement but don't see any obvious damage but O rings are very different size from 1 side to the other don't know if 1 stretched that much or was wrong to start with. also if I...
by dagnblond
Sun May 31, 2020 8:36 am
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

are there measurements I can check or anything . I was hoping that it would be easy and cheap . but not usually my luck
by dagnblond
Sun May 31, 2020 6:11 am
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

not that I can see, haven't taken anything apart yet as I've been busy around here but I should be able to take some time on it this week
by dagnblond
Sat May 30, 2020 7:13 pm
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

can't really tell what exactly happened, both lift arms are flush with end of shaft. as soon as I get a chance I want to loosen the bolts and see if the lift arms will slide in a little or if there's any odd movement or bolt hole wobbled out or whatever. was just wondering about just replacing all O...
by dagnblond
Sat May 30, 2020 1:53 pm
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

do you guys think I need to rebuild the lift control or just replace seals on the lift arms
by dagnblond
Fri May 29, 2020 2:13 pm
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

thanks guys , finally got a chance to look it over and looks like it did shove a seal out the side of the lift
tractor lift 2.jpg
tractor lift 2.jpg (131.04 KiB) Viewed 798 times
tractor lift 1.jpg
tractor lift 1.jpg (151.4 KiB) Viewed 798 times
by dagnblond
Tue May 26, 2020 11:28 pm
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

Re: 1401 3 point drops

handle stays where I put it and arms seem parallel
by dagnblond
Tue May 26, 2020 7:01 am
Forum: Tech Support
Topic: 1401 3 point drops
Replies: 25
Views: 1397

1401 3 point drops

I've got a 1401D and when I was backdragging a driveway one of the lift pins on the 3 point sheared off dropping one corner of the box blade into the sand bringing me to a very abrupt stop. now after replacing both pins the 3 point will not stay up so I have to constantly lift it back up. any clues ...
by dagnblond
Wed Jan 22, 2020 6:33 pm
Forum: Tech Support
Topic: HARBOR FREIGHT QUICK HITCH
Replies: 15
Views: 6253

Re: HARBOR FREIGHT QUICK HITCH

qh3.jpg
Pats connected
qh3.jpg (201.78 KiB) Viewed 864 times

Go to advanced search