Search found 56 matches

by sutto55
Thu Jan 14, 2021 6:01 am
Forum: Tech Support
Topic: Another 3pt wont lift question Yanmar 336
Replies: 6
Views: 349

Re: Another 3pt wont lift question Yanmar 336

OK. Problem solved. I removed the suction hose #53 between the Filter and Pump and I cleaned it up found this. One thing that did surprise me was that when I pulled the line off the filter, I was all ready with funnel and bucket to catch all the oil and none came out. I had a bit from the other end ...
by sutto55
Tue Jan 12, 2021 4:48 pm
Forum: Tech Support
Topic: Instrument panel
Replies: 20
Views: 2101

Re: Instrument panel

OK, That makes sense.

Yes, Probably regulator.
by sutto55
Tue Jan 12, 2021 4:41 pm
Forum: Tech Support
Topic: Another 3pt wont lift question Yanmar 336
Replies: 6
Views: 349

Re: Another 3pt wont lift question Yanmar 336

Hi Winston, I agree the bubbles are a concern. The only point I can find that is doubtful is Item#53 below. This is a rubber hose that connects to the suction line going to the pump that has a coating of oil on it. There is no oil dripping from it though when engine is stopped. The other rubber hose...
by sutto55
Mon Jan 11, 2021 4:22 pm
Forum: Tech Support
Topic: Instrument panel
Replies: 20
Views: 2101

Re: Instrument panel

OK, From your previous post you say " It looks like the regulator has a red wire from it to the starter where it jumps back to to the battery thru the positive wire. Since I have nothing at the battery, it must not be coming from the regulator." When you say you have nothing at the battery...
by sutto55
Mon Jan 11, 2021 3:47 pm
Forum: Tech Support
Topic: Instrument panel
Replies: 20
Views: 2101

Re: Instrument panel

Easiest way to check if the Alternator is working. First off, is it an Alternator or Dynamo/generator? your post says Alternator and the schematic shows a Generator. Not that anything below would be different. An Alternator outputs AC (sort of!). Some Alternators have an internal diode network to re...
by sutto55
Mon Jan 11, 2021 2:24 pm
Forum: Tech Support
Topic: Another 3pt wont lift question Yanmar 336
Replies: 6
Views: 349

Re: Another 3pt wont lift question Yanmar 336

Hi Winston, I didnt do anything at the time. The 336 was fairly new to me at the time and I think it was just the difference between the YM165 that the hydraulics was a bit slower and smoother and when I got used to the difference I didnt see it as such an issue. In this instance before it stopped m...
by sutto55
Mon Jan 11, 2021 12:14 am
Forum: Tech Support
Topic: Another 3pt wont lift question Yanmar 336
Replies: 6
Views: 349

Another 3pt wont lift question Yanmar 336

I recently changed the Transmission/Hydraulic oil in my 336 tractor. Cleaned the suction screen. Replaced the Filter. Checked the oil level and topped it off to full. The 3pt would lift but slowly before that and the items above did not really make any difference. Since then it has been getting slow...
by sutto55
Sun Sep 13, 2015 6:42 pm
Forum: Tech Support
Topic: John Deere 950 (YM336D) engine speed problem
Replies: 10
Views: 8274

Re: John Deere 950 (YM336D) engine speed problem

One thing to be aware of if you remove the pump is to set the fuel rack into the centre. The travel allows the rack out far enough to jam on the housing. The other problem I had was installing the new pump. The spring clips on the back required some persuasion to get them into the block to allow the...
by sutto55
Mon Aug 31, 2015 9:50 pm
Forum: Tech Support
Topic: John Deere 950 (YM336D) engine speed problem
Replies: 10
Views: 8274

Re: John Deere 950 (YM336D) engine speed problem

I had the same issue with my engine. After changing pump and adjusting eventually got it running with help from this site. All was good except for the hunting at low throttle. Ended up the throttle shaft that goes from outside connected to the throttle lever through the block and connects inside to ...
by sutto55
Wed Jul 08, 2015 2:13 am
Forum: Tech Support
Topic: Paint
Replies: 4
Views: 3158

Re: Paint

I had mine checked at the local crash repairs. They tell me the spectrometer they use gives a rating of how close to the original the match is on a scale of 0 to 16. Zero being an exact match. They came up with a 1981/1982 Rover colour called Cinnabar. The match was a 5 which he said if he was repai...
by sutto55
Tue Jun 23, 2015 3:37 am
Forum: Tech Support
Topic: YM336 Diff Lock
Replies: 9
Views: 4399

Re: YM336 Diff Lock

Have been using the grader blade for the last couple of days and found that I can get it to lock in if I push the lever down, just as the wheel starts to slip. Guess it must have been a bit tight maybe from lack of use, but all seems good now.

sutto55
by sutto55
Tue Jun 23, 2015 3:34 am
Forum: Tech Support
Topic: YM336 Hydraulics
Replies: 1
Views: 1663

YM336 Hydraulics

A question on the hydraulics on my YM336. When I run the 3 pt hitch up and down its a bit jerky. As yet I havent done anything like changing oil, cleaning screens/filters etc. Just looking for ideas of what it could be as I would hate to change oil / filters etc and then find out there is something ...
by sutto55
Wed May 27, 2015 2:49 pm
Forum: Tech Support
Topic: Yanmar 155D Category 1 or Category 0 ???
Replies: 5
Views: 3765

Re: Yanmar 155D Category 1 or Category 0 ???

Yanmar rims are offset and often installed to minimize the track (distance between rear outsides). If that applies to yours and you need more space between the rear insides, remove a rear, pivot it so the outside becomes the inside, re-install, and repeat with the other. Just a question on this. I ...
by sutto55
Fri May 08, 2015 4:39 am
Forum: Tech Support
Topic: YM336 Diff Lock
Replies: 9
Views: 4399

Re: YM336 Diff Lock

I checked a bit closer of the setup.

The pedal moves freely no problem. When you press down on the pedal it pushes on a pin that comes out the side of the diff/ transmission. The pin pushes in about 1/4" when pushing on the pedal and then comes to a dead stop.

sutto55
by sutto55
Wed Apr 29, 2015 5:17 am
Forum: Tech Support
Topic: YM336 Diff Lock
Replies: 9
Views: 4399

Re: YM336 Diff Lock

Thanks for the comments guys. I might just run it and see how many times I could use it and make a decision which way to go.

I was hoping it would be an easy fix as there is an inspection plate just above it, but it may be more difficult than I thought.

sutto55

Go to advanced search