Search found 67 matches

by 4x4_Welder
Fri Aug 04, 2017 4:48 pm
Forum: Tech Support
Topic: oil in radiator
Replies: 2
Views: 342

Re: oil in radiator

If there is an oil cooler that is the first place I would look. The oil is under higher pressure than the coolant, and will force through a smaller crack than the coolant can.
by 4x4_Welder
Fri Aug 04, 2017 4:43 pm
Forum: Tech Support
Topic: Brakes and three point hitch not working
Replies: 6
Views: 405

Re: Brakes and three point hitch not working

On my 135D, the valve the 3pt lever moves was seized. I pulled it (easy), and soaked it in parts wash solvent for a couple days, gave it a tap and it was free.
by 4x4_Welder
Mon Jan 23, 2017 10:25 pm
Forum: Classifieds Section
Topic: YM135D/155D mid mount plates and sleeve hitch
Replies: 0
Views: 414

YM135D/155D mid mount plates and sleeve hitch

I have made a few upgrade parts for my YM135D and thought I'd share. First is a pair of plates that I made to mount a snowblower, and will eventually use to mount a mid mount grader blade. 1/4" steel, mount to the four bolts that connect the front frame to engine block. http://i105.photobucket....
by 4x4_Welder
Mon Jan 23, 2017 10:07 pm
Forum: Tractor Projects With Images!
Topic: Adapted snowblower and future expandability
Replies: 5
Views: 852

Re: Adapted snowblower and future expandability

Better pic of the belt drive to the prop shaft. http://i105.photobucket.com/albums/m223/JROCK4x4/KIMG0264_zpsvrt7spr4.jpg I think I'll rework this eventually, with a better tensioner system to take the load off the PTO shaft, and transmit power a bit more reliably. Maybe an actual chaincase with a P...
by 4x4_Welder
Mon Jan 16, 2017 7:26 pm
Forum: Tractor Projects With Images!
Topic: Adapted snowblower and future expandability
Replies: 5
Views: 852

Re: Adapted snowblower and future expandability

45 tooth worn out driven sprocket to a 30tooth new one: http://i105.photobucket.com/albums/m223/JROCK4x4/Mobile%20Uploads/2017-01/KIMG0257_zpsy2e4tyw3.jpg 15tooth drive sprocket, so if my math is somewhat correct: 3.95" drive pulley and 2.95" driven, at 800rpm gives me about 1070 rpm at th...
by 4x4_Welder
Fri Jan 13, 2017 3:20 pm
Forum: Tractor Projects With Images!
Topic: Adapted snowblower and future expandability
Replies: 5
Views: 852

Adapted snowblower and future expandability

I have a YM135D, and a 46" Craftsman snowblower that were not designed to get along together. This winter was forecast to be pretty rough, so I needed some heavy duty snow removal equipment up and running. There was a lot of adapting required, but that's what I do. First was the mid mount plate...
by 4x4_Welder
Fri Jan 13, 2017 2:55 pm
Forum: Tech Support
Topic: Hydraulic pump
Replies: 36
Views: 2239

Re: Hydraulic pump

It'll freeze and crack the pump most likely. The fluid will also turn milky if there is aeration, like if there is an air leak at the hose section on the suction line from the pump to the trans.
by 4x4_Welder
Fri Jan 13, 2017 2:50 pm
Forum: Tech Support
Topic: crankshaft specs for 2tr15
Replies: 2
Views: 352

Re: crankshaft specs for 2tr15

Is that the same crank as the 2TR13A and 2T73A?
The throw is 1.8484-1.8489, and the main journals are 2.5570-2.5576
This crank is also extremely difficult to do anything with as there is no center main bearing.
by 4x4_Welder
Wed Dec 28, 2016 12:36 am
Forum: Tech Support
Topic: Pulley for rear PTO
Replies: 10
Views: 878

Re: Pulley for rear PTO

Thanks. I had thought about using the front pulley PTO but since the snowblower I had already had a driveshaft to the rear mount point I went that route. Plus the engine actually turns the opposite direction of the PTO so it would take some extra work to make that functional. I run the PTO on the hi...
by 4x4_Welder
Tue Dec 27, 2016 2:49 pm
Forum: Tech Support
Topic: Pulley for rear PTO
Replies: 10
Views: 878

Re: Pulley for rear PTO

I used an H hub pulley as recommended by Winston above. I made a driveshaft from telescoping square tube with 3/4" round stock on either end to run in pillow blocks and attach to a universal joint. Unfortunately the snowblower's driveshaft was actually 7/8" so I had to permanently modify a...
by 4x4_Welder
Sun Dec 25, 2016 3:03 pm
Forum: Tech Support
Topic: Hydro pump deadheading
Replies: 7
Views: 569

Re: Hydro pump deadheading

What condition are the key ways in? I have a car that is notorious for losing the crank sprocket key due to the keyways hogging out over time. if the keyways are anything other than straight and clean with square edges a new key alone won't fix the issue. Make sure that the keyway in the gear is ok,...
by 4x4_Welder
Sun Dec 25, 2016 1:56 am
Forum: Tech Support
Topic: Pulley for rear PTO
Replies: 10
Views: 878

Re: Pulley for rear PTO

http://i105.photobucket.com/albums/m223/JROCK4x4/KIMG0220_zps7byrljaa.jpg http://i105.photobucket.com/albums/m223/JROCK4x4/KIMG0219_zps0hrh8fes.jpg It's mounted and had about 4hrs use today. The drive ratio isn't high enough, but i don't want to drive the shaft any faster, so I am going to change t...
by 4x4_Welder
Sat Dec 10, 2016 7:32 pm
Forum: Tech Support
Topic: Pulley for rear PTO
Replies: 10
Views: 878

Re: Pulley for rear PTO

Plates made and installed: http://i105.photobucket.com/albums/m223/JROCK4x4/KIMG0206_zpsjdqscndd.jpg The snowblower will use the lower rear mount hole, but I like options. It'll also let me run a parallelogram linkage for a vertical lift mid mount grader at some point in the future. I do have a temp...
by 4x4_Welder
Sun Dec 04, 2016 8:01 pm
Forum: Tech Support
Topic: Pulley for rear PTO
Replies: 10
Views: 878

Re: Pulley for rear PTO

Thanks. I had done a few searches specifically for an H bushing but nothing came up. Got one sitting here now. I made the template for the mid-mount support plates today, they will bolt outside the front frame bars using the engine bolts. I set up four mount options for later use. I plan to build a ...
by 4x4_Welder
Sun Nov 06, 2016 11:26 pm
Forum: Tech Support
Topic: Pulley for rear PTO
Replies: 10
Views: 878

Pulley for rear PTO

I am attempting to mount my 46" snowblower on my 135d, but can't seem to locate a part. I had looked everything up a year or so back, but now I cannot find a pulley that fits on the rear PTO stub. I need to drive a pair of 1/2 or 5/8" vee belts. Does anyone know where to find one of these?

Go to advanced search