Search found 4967 matches

by winston
Tue Jun 18, 2019 4:38 am
Forum: Tech Support
Topic: Engine Rebuild Gone Bad
Replies: 15
Views: 455

Re: Engine Rebuild Gone Bad

Although I don't think I have ever seen that before it would appear your head has holes in it. The way it is pitted would lead you to believe it sat on the ground for a long period of time. New heads are expensive but you may be facing that. I suppose no harm could come from trying a little liquid m...
by winston
Mon Jun 17, 2019 10:46 am
Forum: Tech Support
Topic: Engine Rebuild Gone Bad
Replies: 15
Views: 455

Re: Engine Rebuild Gone Bad

Probably what bent the push rod when the overtightened valve hit the piston. Valves must be allowed to close completely, that is why you have the clearance between the rocker arm and valve.
by winston
Sun Jun 16, 2019 5:24 am
Forum: Classifieds Section
Topic: Want to buyYanmar 180D front PTO clutch
Replies: 1
Views: 41

Re: Want to buyYanmar 180D front PTO clutch

Assuming you are wanting an over run clutch and not a slip clutch? https://www.hoyetractor.com/PROD/OR-660.htm The 180 may have an internal over run clutch as this picture of a 186 shows with #13 & #14. Hoye can answer the question for you. The 186 is a power shift and yours a geared transmission.
by winston
Sat Jun 15, 2019 10:43 am
Forum: Tech Support
Topic: YM165D tachometer/hourmeter ratios
Replies: 7
Views: 149

Re: YM165D tachometer/hourmeter ratios

mctank wrote:I also need hourmeter ratio.


Back to my first statement, good luck with that, I'll be surprised if you can come up with it. I am supposing that would be how many turns per second? at 2000rpm or something along those lines.
by winston
Fri Jun 14, 2019 3:25 pm
Forum: Tech Support
Topic: John Deere 650
Replies: 6
Views: 124

Re: John Deere 650

John Deere parts sight is readily available. They show 3 different valves, no idea which one you have. Thinking you might replace a couple of O-rings and maybe the end seal in it and a good clean up job. Tolerances are very close in it. I would imagine this sight could help you with the parts that a...
by winston
Fri Jun 14, 2019 8:59 am
Forum: Tech Support
Topic: John Deere 650
Replies: 6
Views: 124

Re: John Deere 650

That is the control valve. The lever your are talking about is the drop speed lever. It control how fast your 3 point goes down.
by winston
Fri Jun 14, 2019 4:34 am
Forum: Tech Support
Topic: No Oil Pressure after overhaul on ym155d
Replies: 3
Views: 110

Re: No Oil Pressure after overhaul on ym155d

Don't know how to do it but you might ponder on removing the oil pressure sensor, use the opening to attach some kind of pressured oil introduction that might force oil through the system and into the pump. If it were to work you might have to drain out a little oil. Just a crazy idea but I wouldn't...
by winston
Fri Jun 14, 2019 4:27 am
Forum: Tech Support
Topic: 336D Powershift transmission issue
Replies: 19
Views: 3262

Re: 336D Powershift transmission issue

Your tractor has the same setup. https://www.hoyetractor.com/PROD/SC-4300.htm

Hopefully Wiseman will be along with his help but this might help you if you go for the split. https://youtu.be/HVb58N-gdhU
by winston
Fri Jun 14, 2019 4:16 am
Forum: Tech Support
Topic: John Deere 650
Replies: 6
Views: 124

Re: John Deere 650

Not sure what lever you are talking about. The feedback rod (#51) is on the end of the rockshaft but it the rockshaft moves the feedback rod would have to move. It does sound like your piston o-ring (#10) is leaking. https://partscatalog.deere.com/jdrc/sidebyside/equipment/71728/referrer/navigation/...
by winston
Thu Jun 13, 2019 5:38 pm
Forum: Tech Support
Topic: YM165D tachometer/hourmeter ratios
Replies: 7
Views: 149

Re: YM165D tachometer/hourmeter ratios

That would give you the engine to tach cable ratio which I guess is what you are really wanting.
by winston
Thu Jun 13, 2019 12:07 pm
Forum: Tech Support
Topic: YM165D tachometer/hourmeter ratios
Replies: 7
Views: 149

Re: YM165D tachometer/hourmeter ratios

Wow, good luck with that. :shock:
by winston
Wed Jun 12, 2019 4:12 am
Forum: Tech Support
Topic: Bare minimum to fix 4wd knuckle leak?
Replies: 6
Views: 194

Re: Bare minimum to fix 4wd knuckle leak?

Based on your measurements you must have the old style. https://www.hoyetractor.com/CTGY/3364WDEXT-OLD.htm

Hoping you have read this also. https://www.hoyetractor.com/PROD/AS-6064.htm
by winston
Mon Jun 10, 2019 5:07 pm
Forum: Tech Support
Topic: Weird Starting Problem
Replies: 2
Views: 92

Re: Weird Starting Problem

Where did you attach the leads when you jump started? Sort of sounding like your ground connection at frame needs taken loose and cleaned.
by winston
Fri Jun 07, 2019 2:48 pm
Forum: Tech Support
Topic: Bare minimum to fix 4wd knuckle leak?
Replies: 6
Views: 194

Re: Bare minimum to fix 4wd knuckle leak?

May also have worn bearings.
by winston
Thu Jun 06, 2019 5:10 pm
Forum: Tech Support
Topic: YM2000B Temperature Guage
Replies: 4
Views: 185

Re: YM2000B Temperature Guage

I used a 5 footer for several years with my old 2002D, same hp you have, just had to use good common sense with it. You don't have to take a full 5 foot cut.

Go to advanced search