Search found 3469 matches

by Aaron
Thu Apr 15, 2021 10:03 am
Forum: Tech Support
Topic: My ym2010d clutch adjustment
Replies: 31
Views: 3500

Re: My ym2010d clutch adjustment

As I have mentioned several times- the PTO function is a critical fork in the troubleshooting path. I know you don't care if the PTO works or not BUT without (reliably) knowing if the PTO works under a load I can not help you decide which way to go- powershift or mechanical. You need to be very meth...
by Aaron
Wed Apr 14, 2021 8:54 am
Forum: Tech Support
Topic: Yanmar 1510- 3 pt. wont raise
Replies: 1
Views: 37

Re: Yanmar 1510- 3 pt. wont raise

Will the three point lift without any weight on it? If you can get the arms to raise (on their own hydraulic power - not you picking them up) then you can close the lockout valve and see if they will fall back down. That will indicate blown/leaking orings on the lift piston. Otherwise it might be a ...
by Aaron
Tue Apr 13, 2021 1:08 pm
Forum: Tech Support
Topic: Excavator Starting / Hydraulic issues
Replies: 4
Views: 71

Re: Excavator Starting / Hydraulic issues

I think a version of that model was also sold in the USA (non grey market) so there should be English service manuals out there and dealer support for that USA version.
by Aaron
Mon Apr 12, 2021 1:01 pm
Forum: Tech Support
Topic: 187D clutch replacement
Replies: 3
Views: 48

Re: 187D clutch replacement

I thought I might have one of those plastic lineup tools here but it was for a bigger spline. I would probably take my clutch & pilot bushing to an auto parts store and see if you can match up a lineup tool. I bet there is some car out there that uses the same splines.
by Aaron
Mon Apr 12, 2021 12:56 pm
Forum: Tech Support
Topic: YM1510 D front drive
Replies: 1
Views: 33

Re: YM1510 D front drive

I guess anything can be made to fit but no- the 1500D 4wd assembly will not be anything close to a direct replacement for the 1510D. Could it be made to fit? Yes- but it would require quite a lot of fabrication. Different driveshaft style, different mounting setup, and I'm not sure if the gear ratio...
by Aaron
Mon Apr 12, 2021 11:45 am
Forum: Tech Support
Topic: 187D clutch replacement
Replies: 3
Views: 48

Re: 187D clutch replacement

Ye the 187 is the only Yanmar that I'm aware of that has that setup. Removing the clutch shaft on the 187 is MUCH more difficult than it should be. I dont have a line up tool (because every other Yanmar just uses the clutch shaft itself) but I will see if I can find something that will work.
by Aaron
Mon Apr 12, 2021 11:39 am
Forum: Tech Support
Topic: steering shaft problem ym-135
Replies: 1
Views: 28

Re: steering shaft problem ym-135

The adjustment screw does not have anything to do with up and down movement. The up and down motion of that shaft is controlled by the preload of the steering shaft bearings (shims between the steering tube & steering box). The most common cause for that much movement is the bottom bearing getti...
by Aaron
Fri Apr 09, 2021 9:33 am
Forum: Tech Support
Topic: F15 3 point hitch HELP!
Replies: 5
Views: 134

Re: F15 3 point hitch HELP!

There is not a kit but we should have the individual pieces. Just click the contact us link below or give our parts guys a call at 940-592-0181
by Aaron
Thu Apr 08, 2021 12:12 pm
Forum: Tech Support
Topic: Purchased a Yanmar this weekend, how do I tell what I have?
Replies: 1
Views: 70

Re: Purchased a Yanmar this weekend, how do I tell what I have?

If you are having trouble uploading a picture you can use a free image resizing program like: http://www.picresize.com There is nothing to download. It is free. It is all done on the website and it will allow you to reduce the size of the image to a reasonable size for uploading.
by Aaron
Thu Apr 08, 2021 9:03 am
Forum: Tech Support
Topic: YM 186 Rod End Cap Bolt Torque Specs.
Replies: 2
Views: 50

Re: YM 186 Rod End Cap Bolt Torque Specs.

The original Yanmar manual says 16.6-20.2 ft/lbs. I always think it is funny that they give such precise torque numbers... but in a range spanning several ft/lbs. 16.6 to 20.2? Why not just say 17 to 20 or better yet why not just 18? :lol:

1.jpg
1.jpg (30.84 KiB) Viewed 47 times
by Aaron
Wed Apr 07, 2021 12:21 pm
Forum: Tech Support
Topic: 226d Headlight bulb holder
Replies: 4
Views: 96

Re: 226d Headlight bulb holder

That one Winston posted sure looks like it could be adapted to work pretty easily. I have tried to find direct replacements before but have not found anything.
by Aaron
Tue Apr 06, 2021 2:37 pm
Forum: Tech Support
Topic: YM2000 Hydraulic Hoses
Replies: 1
Views: 57

Re: YM2000 Hydraulic Hoses

Just mark them all carefully and take them to a local hydraulic shop. Many NAPA auto parts stores also make hydraulic hoses while you wait. Or you can order them from surpluscenter.com by the length & fitting type.
by Aaron
Tue Apr 06, 2021 2:11 pm
Forum: Tech Support
Topic: 4WD Tire issue
Replies: 16
Views: 357

Re: 4WD Tire issue

Oh the ratios are certainly important and you should try to get it as close as possible. BUT... you will probably never have it matched perfectly and, if it is not perfect, then you need to be sure to only use 4wd when needed so the surface conditions can absorb the difference the front & rear t...
by Aaron
Tue Apr 06, 2021 10:54 am
Forum: Tech Support
Topic: Shifting problem
Replies: 11
Views: 256

Re: Shifting problem

I don't think there are specific torques for those. You would just use a torque chart like below.
https://www.bing.com/images/search?q=me ... que+chart&

Go to advanced search