Search found 2847 matches

by Aaron
Thu Mar 21, 2019 1:39 pm
Forum: Tech Support
Topic: Yanmar 2001D 4X4
Replies: 43
Views: 1283

Re: Yanmar 2001D 4X4

Here are a couple clutches that are installed correctly. The fingers are almost flat which is pretty much the same as your new clutch setup in your video.

1.jpg
1.jpg (42.41 KiB) Viewed 18 times

2.jpg
2.jpg (29.12 KiB) Viewed 18 times
by Aaron
Thu Mar 21, 2019 11:12 am
Forum: Tech Support
Topic: Yanmar 2001D 4X4
Replies: 43
Views: 1283

Re: Yanmar 2001D 4X4

I got your pictures of the old clutch. It looks like you are not checking back for my replies to your support tickets so I will respond here as well. Your old pressure plate looks even worse so I'm not really sure what is causing the fingers to be inverted like that. is it possible that someone mach...
by Aaron
Mon Mar 18, 2019 2:33 pm
Forum: Tech Support
Topic: 1720D ROPS - just need the top piece
Replies: 11
Views: 163

Re: 1720D ROPS - just need the top piece

I'm not an engineer and I'm not going to pretend to be but I have built a lot of stuff and just sort of have a feel for what will work and what won't. To be sure that I take any potential profit out of the equation I will sell you this rops at my cost should you chose to buy it. I will give you a co...
by Aaron
Mon Mar 18, 2019 1:19 pm
Forum: Tech Support
Topic: 1720D ROPS - just need the top piece
Replies: 11
Views: 163

Re: 1720D ROPS - just need the top piece

I'm not really sure those were ever intended to be a ROPS. I have had a couple in here and thought they were really just more of a sun shade support. Not very sturdy at all. I would certainly not operate the tractor in a way where I was relying on it to save my life (because it probably would not). ...
by Aaron
Fri Mar 15, 2019 10:37 am
Forum: Tech Support
Topic: My mistake tractor is 1510d not 1610d no reverse, need fluid change
Replies: 9
Views: 159

Re: My mistake tractor is 1510d not 1610d no reverse, need fluid change

There are two (book only shows one but says 'qty 2'). The draining is in the first part of the video below. I only drain one in the video but it will give you the basic idea.
https://www.hoyetractor.com/PTOSealVideo.htm
by Aaron
Thu Mar 14, 2019 12:42 pm
Forum: Tech Support
Topic: My mistake tractor is 1510d not 1610d no reverse, need fluid change
Replies: 9
Views: 159

Re: 1610d no reverse, need fluid change

The drain plug and the cover over the hydraulic screen are highlighted below. I would just let all of the hydraulics (loader and tph) rest on the ground (for safety) and change the oil. I don't really know why it would need to be warm and really dont know what 2wd or 4wd would have anything to do wi...
by Aaron
Thu Mar 14, 2019 12:38 pm
Forum: Tech Support
Topic: Yanmar 186 servicing
Replies: 1
Views: 71

Re: Yanmar 186 servicing

The recommended oils can be found here
https://www.hoyetractor.com/support/kno ... ?article=1


The transmission dipstick is below

1.jpg
1.jpg (57.57 KiB) Viewed 63 times
by Aaron
Tue Mar 12, 2019 3:00 pm
Forum: Tech Support
Topic: New battery, clean terminals on both ends- no turn over
Replies: 13
Views: 258

Re: New battery, clean terminals on both ends- no turn over

But a starter problem would not cause this:

If I disconnect one of the terminals and reconnect sometimes I'll see the red instrument lights until I turn the key over - then nothing at all.
by Aaron
Tue Mar 12, 2019 1:15 pm
Forum: Tech Support
Topic: New battery, clean terminals on both ends- no turn over
Replies: 13
Views: 258

Re: New battery, clean terminals on both ends- no turn over

hrtull wrote: Put the tractor in neutral, brakes on. Take a jumper wire and go directly from battery to the spade terminal on the solenoid which is the light gauge wire from switch that is suppose to trigger solenoid. . Just touch it and see if you get a response from the solenoid. If you do proble...
by Aaron
Tue Mar 12, 2019 1:04 pm
Forum: Tech Support
Topic: New battery, clean terminals on both ends- no turn over
Replies: 13
Views: 258

Re: New battery, clean terminals on both ends- no turn over

You will just need to check the voltages while running the starter (attempting to run the starter) and see where the voltage drops. If the voltage stays strong at the battery then move up to the terminal on the starter. At some point I feel like you will see 12v with the key off and then 0v when you...
by Aaron
Tue Mar 12, 2019 12:04 pm
Forum: Tech Support
Topic: Glow plug help
Replies: 1
Views: 69

Re: Glow plug help

Glow plugs just make the engine easier to start- especially when it is cold. Not using the glow plugs wont really hurt anything other than putting extra wear on your starter. Failure to use the glow plugs will not damage them.
by Aaron
Sat Mar 09, 2019 5:40 pm
Forum: Tech Support
Topic: Tach./ Speedometer
Replies: 2
Views: 115

Re: Tach./ Speedometer

The most common failure point is the cable. It runs from the dash to the front of the engine.
https://www.hoyetractor.com/CTGY/F32.htm
by Aaron
Mon Mar 04, 2019 10:39 am
Forum: Tech Support
Topic: Hydraulic pump drive coupler
Replies: 3
Views: 147

Re: Hydraulic pump drive coupler

It is just keyed and a pretty tight fit. You might need to use a puller.
by Aaron
Fri Mar 01, 2019 12:07 pm
Forum: Tech Support
Topic: yanmar 135D antifreeze out overflow
Replies: 1
Views: 131

Re: yanmar 135D antifreeze out overflow

It is normal (and necessary) for some coolant to come out of that tube when the coolant gets warm and expands. That is why it is there. If you have a recovery bottle there then it can suck it back in as it cools. If the radiator cap is leaking then it can allow more coolant to leave than necessary. ...
by Aaron
Wed Feb 27, 2019 2:46 pm
Forum: Tech Support
Topic: Yanmar YM1300D hood question/front drive slop
Replies: 3
Views: 232

Re: Yanmar YM1300D hood question/front drive slop

Sorry I do not have a YM1300 here with enough hood parts still together that would help. The front drive works in 4x4, but the knuckles seem to have a lot of play/slop from side to side. Is there something I can tighten up, or will parts need to be replaced? You will really just need to jack up the ...

Go to advanced search