Search found 3411 matches

by Aaron
Sat Feb 27, 2021 7:49 pm
Forum: Tech Support
Topic: YM_240D RADIATOR INSTALL (DRAIN PROBLEM)
Replies: 1
Views: 11

Re: YM_240D RADIATOR INSTALL (DRAIN PROBLEM)

Im not really sure what that would be but it does not sound like a drain. I will check one out on Monday and see if I can find what you are describing but would you be able to attach a picture of what you are describing?
by Aaron
Fri Feb 26, 2021 9:07 am
Forum: Tech Support
Topic: Rear axle removal. 1401d
Replies: 47
Views: 2509

Re: Rear axle removal. 1401d

The factory style seal on the 1401 uses an integrated wear collar and the assembly can be a little finicky. A standard seal seems to be a little more tolerant but just does not have that wear collar built in. I agree with Winston that if you axle is moving then you should double check your bearings ...
by Aaron
Mon Feb 22, 2021 10:03 am
Forum: Tech Support
Topic: YM276D 4x4 will not engage
Replies: 6
Views: 99

Re: YM276D 4x4 will not engage

With the tractor in 2wd you will be able to spin the front tires independently so really anything in the 4wd system could cause that. You will probably just have to do some more investigating. It could be that there is a gear or shaft broken or even something missing. We've heard many customers say ...
by Aaron
Mon Feb 22, 2021 9:55 am
Forum: Tech Support
Topic: Hydraulic question.
Replies: 1
Views: 42

Re: Hydraulic question.

Loader valves will typically have a built in relief to protect the loader circuit (think of it like a fuse or circuit breaker) but it will not protect anything before or after the loader valve. If the loader cylinders stall out (maximum travel or lifting something too heavy) the relief valve bypasse...
by Aaron
Mon Feb 22, 2021 9:49 am
Forum: Tech Support
Topic: YM2210 manual gears shift locks up rear end
Replies: 4
Views: 52

Re: YM2210 manual gears shift locks up rear end

That is typically caused by the shift fork being stuck in one gear (the shift lever slips out of the fork and leaves the gear engaged). Trying to put it into a different gear puts the transmission in a bind since you cant go two speeds at once. Does the tractor try to move when in neutral?
by Aaron
Fri Feb 19, 2021 2:29 pm
Forum: Implements
Topic: cylinder
Replies: 1
Views: 15

Re: cylinder

Your best bet will be to take your old cylinder to a local hydraulic shop to get it repaired or, if it is not repairable, they can match it up to a new cylinder that will fit. I doubt you will find those cylinders from Yanmar anymore and the company that built the loader for Yanmar is out of busines...
by Aaron
Fri Feb 19, 2021 10:08 am
Forum: Tech Support
Topic: Yanmar EX3200 - where does this tube go?
Replies: 8
Views: 170

Re: Yanmar EX3200 - where does this tube go?

Sorry I do not know but I agree with Winston that something has to connect to that tube or it would collect water/dirt/bugs. That hose being right there sure seems like the most likely solution but I don't know for 100%. One of the guys on the 'new Yanmar' Tractorbynet forum that has an EX320 might ...
by Aaron
Fri Feb 19, 2021 8:56 am
Forum: Tech Support
Topic: YM1500 Surging/Loping/Smoking
Replies: 4
Views: 99

Re: YM1500 Surging/Loping/Smoking

320 is very low compression. The fuel timing is just set by the shims under the pump and is normally just the same shims as the original pump. Did you check the fuel timing using the procedure in the manual?
by Aaron
Thu Feb 18, 2021 3:25 pm
Forum: Tech Support
Topic: YM1500 Surging/Loping/Smoking
Replies: 4
Views: 99

Re: YM1500 Surging/Loping/Smoking

The heavy smoke would seem to indicate unburned fuel- maybe a clogged or misfiring injector. You can test that with the instructions below https://www.hoyetractor.com/support/knowledgebase.php?article=72 The failure to maintain an RPM is almost always caused by the rack being sticky or the governor ...
by Aaron
Thu Feb 18, 2021 1:23 pm
Forum: Tech Support
Topic: Yanmar EX3200 - where does this tube go?
Replies: 8
Views: 170

Re: Yanmar EX3200 - where does this tube go?

The older YM Yanmars did the same thing just without the hose

https://www.hoyetractor.com/PROD/AB-42280.htm
Image
by Aaron
Thu Feb 18, 2021 1:22 pm
Forum: Tech Support
Topic: YM 1510d Power Steering
Replies: 3
Views: 90

Re: YM 1510d Power Steering

Sorry I do not know what the ideal stroke length would be. You should be able to get pretty close just by measuring the travel of your old steering box's pitman arm. You could always thread the end of the cylinder and screw a tie rod right onto the end of the cylinder to safe length. It would be a c...
by Aaron
Thu Feb 18, 2021 1:17 pm
Forum: Tech Support
Topic: Over full hydraulic oil
Replies: 2
Views: 83

Re: Over full hydraulic oil

I, personally, would not worry about it but I don't have any actual data or sources to back that up- so continue at your own risk :D . It also would not take much to drain that little bit extra out if you were worried about it.
by Aaron
Thu Feb 18, 2021 12:56 pm
Forum: Tech Support
Topic: Sudden Excessive Blow By
Replies: 18
Views: 1655

Re: Sudden Excessive Blow By

even the 300psi cylinders are quite a bit below that engine's lower limit. 1.jpg 1.jpg An injector that 'squirts' instead of misting the fuel can cause unburned liquid fuel to collect in the combustion area (fuel flooding I think it is called) and would certainly put a lot of stress on the piston gr...
by Aaron
Thu Feb 18, 2021 11:11 am
Forum: Specs, Capacities, Other
Topic: YM2610d, 3T80-d specs
Replies: 1
Views: 25

Re: YM2610d, 3T80-d specs

1.jpg
1.jpg (14.84 KiB) Viewed 23 times
by Aaron
Tue Feb 16, 2021 11:13 am
Forum: Tech Support
Topic: 2010
Replies: 1
Views: 51

How many hours are to many?

800 hours is still very low. A properly maintained Yanmar can easily see 10,000 or more. That being said, the 2010 you are looking at has probably rolled over so it probably has closer to 1800 or 2800 hours.

Go to advanced search